| Author |
Message |
    
Adam
Rating: N/A
Votes: 0 (Vote!) | | Posted on Monday, January 09, 2006 - 03:00 pm: | 
|
The lever to advance the film is frozen midway. It has been sitting unused for about two years. Is this simply a battery problem? |
Ed
Rating: N/A
Votes: 0 (Vote!) | | Posted on Monday, January 09, 2006 - 03:30 pm: |
|
many possibilities--first, try using a coin or similar to wind via motor dirve connector at bottom of camera--this will eliminate wind head area problems if it works from there. |
Jon Goodman
Rating: N/A
Votes: 0 (Vote!) | | Posted on Tuesday, January 10, 2006 - 10:48 am: |
|
It sounds like it is cocked but the shutter hasn't been fired. Could be a battery problem. I'd try new ones first.
Jon |
adam
Rating: N/A
Votes: 0 (Vote!) | | Posted on Thursday, January 12, 2006 - 06:10 am: |
|
I tried new batteries and that has not worked. I can turn the internal thing that the film attaches to but I cannot get the camera to fire or the film advace arm to move. |
adam
Rating: N/A
Votes: 0 (Vote!) | | Posted on Wednesday, January 18, 2006 - 06:43 pm: |
|
Anyone else? |
Henry
Rating: N/A
Votes: 0 (Vote!) | | Posted on Thursday, January 19, 2006 - 03:20 pm: |
|
First try resetting the camera mechanically. Take a look at https://kyp.hauslendale.com/classics/resetcamera.html
Sadly this resetting article died... no other cameras were added. One reader donated three or four photos of cameras with the bottoms removed but no instructions. And I wasn't familiar with those cameras. Oh well...
Henry |
Adam
Rating: N/A
Votes: 0 (Vote!) | | Posted on Wednesday, January 25, 2006 - 02:10 pm: |
|
Henry,
Thanks. So, (from seeing the picture) I remove the case and pysically unlock it. I can probably figure it out but do you have and suggestions on the process. |
Henry
Rating: N/A
Votes: 0 (Vote!) | | Posted on Wednesday, January 25, 2006 - 06:27 pm: |
|
simply hold the windlock in a disengaged position while winding the camera.
That's it... |
Eric Rogers
Rating: N/A
Votes: 0 (Vote!) | | Posted on Friday, February 17, 2006 - 08:13 pm: |
|
I followed the advise as above, the film advance does not rachet, just goes to the right then returns, any ideas. When I replaced the batteries, when you press the shutter release, the meter will come on, but when you press it harder as to actually release the shutter, the meter goes off.
Thank you |
Andrew
Rating: N/A
Votes: 0 (Vote!) | | Posted on Tuesday, February 21, 2006 - 03:55 pm: |
|
Hey Eric, I have the EXACT same problem, i reset the camera replaced batteries, the meter will come on once when press then nothing.. still locked up.
did you happen to figure out what the problem was?? |
Rebecca
Rating: N/A
Votes: 0 (Vote!) | | Posted on Tuesday, February 21, 2006 - 10:00 pm: |
|
I have a X370n also and i have a problem with the shutter. I can take pictures, but many times the shutter will get stuck and I get a picture that's half black. It happens 70% of the time when I'm using a flash and 20% of the time when I'm using existing light. It doesn't matter if i'm in a warm environment and this has been happening since I bought it in 1993....maybe this is a reason why they discontinued the camera. I've even had it cleaned and "fixed" but it continues to happen. I think I've about had it. My cousins wedding pictures came out half black and un-usable.... If they had a Kelly Blue Book or something for cameras, I wonder if this camera would come up as having frequent problems with its shutter. |
Frida
Tinkerer
Username: Frida
Post Number: 1
Registered: 04-2008
Rating: N/A
Votes: 0 (Vote!) | | Posted on Wednesday, April 02, 2008 - 07:10 pm: |
|
i was pulling my hair out because i bought my XG-M used and after a month of good working order it jammed on me today. After hours of serching online, trying to bypass sending it out and $$ i found this page and the link given by Henry to reset and it worked like magic!!! i registered so I could thank him so, THANKS HENRY!! |
