Author |
Message |
edmundo
Rating: N/A Votes: 0 (Vote!) | Posted on Wednesday, September 15, 2004 - 05:51 am: |
|
Hello all. How do you take off the focus button of a Rolleicord ? The button is turning free, but the lens do not move; actuating the focus on the other side of the camera, it moves OK, so the problem must be the focus button that is not engaging something, but I cannot take off this button! There is some trick ? Thanks. edmundo |
charlie
Rating: N/A Votes: 0 (Vote!) | Posted on Wednesday, September 15, 2004 - 02:09 pm: |
|
Somewhere I read Rolleis are similar to Yashicamats. Under repair manuals on this website there is a Yashicamat manual that seems to show a screw through the center of the focus knob. You may have to peel off a leather disc to get at the screw. Good luck. |
edmundo
Rating: N/A Votes: 0 (Vote!) | Posted on Wednesday, September 15, 2004 - 02:35 pm: |
|
Thanks, Charlie, but this baby is different: on the focus button, there´s no leather, only an aluminun disk with 2 holes, I tried with a plier-spanner, no results. Thanks anyway. edmundo |
Ed
Rating: N/A Votes: 0 (Vote!) | Posted on Sunday, September 19, 2004 - 02:00 pm: |
|
pin spanner should work--naybe dribble a little lighter fluid, etc, around edge to loosen and crud first |
Mark Pearce
Rating: N/A Votes: 0 (Vote!) | Posted on Monday, September 20, 2004 - 08:07 am: |
|
Ed is correct; a pin spanner will turn out the cover disk. Once inside, there is a collet that you can tighten with a spanner or a pair of pliers to secure the knob on the shaft. Top |
edmundo
Rating: N/A Votes: 0 (Vote!) | Posted on Monday, September 20, 2004 - 11:33 am: |
|
Ed and Mark, thank you both. I tried a pin spanner, no results;this thing seems to be definitively locked, no amount of solvent, oil, heat, cold , can unlock it. But Mark, if this is only a cover disk, then I can drill or turn it away, tighten the collet and turn a new disk... the original is pretty damaged anyway... Well, this finishes mechanical faults, I think; now, just assembling the shutter blades,cleaning the lenses (haze), finding a new mirror (maybe a Polaroid one.. and readjusting the focus of the viewing lens...), painting and leathering... I will finish it someday. Again, thank you for the hints. edmundo BTW, the camera is a Rolleicord III with a Triotar. |
Mark Pearce
Rating: N/A Votes: 0 (Vote!) | Posted on Monday, September 20, 2004 - 06:00 pm: |
|
A mirror from a Polaroid OneStep works nicely. I loved my Rolleicord III, as it was mt first good rollfilm camera. It had a great Xenar. Top |
edmundo
Rating: N/A Votes: 0 (Vote!) | Posted on Monday, September 20, 2004 - 08:47 pm: |
|
Thanks Mark, I have a Polaroid somewhere ... I checked again the serial number of the body after cleaning it, seems that is not a III, but a Rolleicord 2 model 6 (Prochnow) or 2 type 5 (Evans). Anyway, good camera, god for repair learning too. Thanks again. This is the best forum i participate, people really helps ! edmundo |
Stuart Willis
Rating: N/A Votes: 0 (Vote!) | Posted on Friday, September 24, 2004 - 08:23 am: |
|
The twin-pin cover on the focusing knobs of 60 year old Rolleis (I just had the identical problem with a 1939 Rolleiflex) require special attention. First clean out all the years of accummulated gunk at the edge. Then a few drops of acetone into that joint an leave overnight. On a quality camera such as this, the pointed pliers method of unscrewing the cap, is a No No. You may have to precision drill (slightly enlarge the pinholes to produce a perfect pair of hole) - and then make up a special tool which also fits perfectly. Broken drill-bit shanks of the right diameter can be sweated into a steel bar. This makes a high integrity tool. But even this may tear away the aluminium cap unless you first "break the stick". Acetone usually works but if it doesn't - then heat most certainly will. No pencil-point butane until well after the acetone had evaporated tho'. Good luck Stuart Willis |
|